#include &tlmm { cam_ois_af_vdd_main_en_default: cam_ois_af_vdd_main_en_default { mux { pins = "gpio60"; function = "gpio"; }; config { pins = "gpio60"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ }; }; cam_ois_af_vdd_tele_en_default: cam_ois_af_vdd_tele_en_default { mux { pins = "gpio61"; function = "gpio"; }; config { pins = "gpio61"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ }; }; }; &soc { cam_ois_af_vdd_main: gpio-regulator@0 { compatible = "regulator-fixed"; reg = <0x00 0x00>; regulator-name = "cam_ois_af_vdd_main"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; regulator-enable-ramp-delay = <233>; enable-active-high; gpio = <&tlmm 60 0>; pinctrl-names = "default"; pinctrl-0 = <&cam_ois_af_vdd_main_en_default>; vin-supply = <&BOB>; }; cam_ois_af_vdd_tele: gpio-regulator@1 { compatible = "regulator-fixed"; reg = <0x01 0x00>; regulator-name = "cam_ois_af_vdd_tele"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; regulator-enable-ramp-delay = <233>; enable-active-high; gpio = <&tlmm 61 0>; pinctrl-names = "default"; pinctrl-0 = <&cam_ois_af_vdd_tele_en_default>; vin-supply = <&BOB>; }; led_flash_rear_main: qcom,camera-flash@0 { cell-index = <0>; compatible = "qcom,camera-flash"; flash-source = <&pmxr2230_flash0>; torch-source = <&pmxr2230_torch0>; switch-source = <&pmxr2230_switch0>; status = "ok"; }; led_flash_rear_uw: qcom,camera-flash@2 { cell-index = <2>; compatible = "qcom,camera-flash"; flash-source = <&pmxr2230_flash0>; torch-source = <&pmxr2230_torch0>; switch-source = <&pmxr2230_switch0>; status = "ok"; }; led_flash_rear_tele: qcom,camera-flash@3 { cell-index = <3>; compatible = "qcom,camera-flash"; flash-source = <&pmxr2230_flash0>; torch-source = <&pmxr2230_torch0>; switch-source = <&pmxr2230_switch0>; status = "ok"; }; qcom,cam-res-mgr { compatible = "qcom,cam-res-mgr"; status = "ok"; }; }; &cam_cci0 { actuator_rear_main: qcom,actuator@0 { cell-index = <0>; compatible = "qcom,actuator"; cci-master = ; cam_vaf-supply = <&cam_64c_ldo4>; regulator-names = "cam_vaf"; rgltr-cntrl-support; rgltr-min-voltage = <2800000>; rgltr-max-voltage = <2800000>; rgltr-load-current = <103000>; status = "ok"; }; eeprom_rear_main: qcom,eeprom@0 { cell-index = <0>; reg = <0x0>; compatible = "qcom,eeprom"; cci-master = ; cam_vio-supply = <&cam_64c_ldo7>; regulator-names = "cam_vio"; rgltr-cntrl-support; rgltr-min-voltage = <1800000>; rgltr-max-voltage = <1800000>; rgltr-load-current = <0>; }; ois_rear_main: qcom,ois@0 { cell-index = <0>; compatible = "qcom,ois"; cci-master = ; cam_vio-supply = <&cam_64c_ldo7>; cam_vaf-supply = <&cam_64c_ldo4>; cam_v_custom1-supply = <&cam_ois_af_vdd_main>; regulator-names = "cam_vio", "cam_vaf", "cam_v_custom1"; rgltr-cntrl-support; rgltr-min-voltage = <1800000 2800000 2800000>; rgltr-max-voltage = <1800000 2800000 2800000>; rgltr-load-current = <14000 119000 119000>; status = "ok"; }; actuator_rear_uw: qcom,actuator@2 { cell-index = <2>; reg = <0x2>; compatible = "qcom,actuator"; cci-master = ; cam_vaf-supply = <&cam_64c_ldo3>; regulator-names = "cam_vaf"; rgltr-cntrl-support; rgltr-min-voltage = <2800000>; rgltr-max-voltage = <2800000>; rgltr-load-current = <100000>; status = "ok"; }; eeprom_rear_uw: qcom,eeprom@2 { cell-index = <2>; reg = <0x2>; compatible = "qcom,eeprom"; cci-master = ; cam_vio-supply = <&cam_64c_ldo7>; regulator-names = "cam_vio"; rgltr-cntrl-support; rgltr-min-voltage = <1800000>; rgltr-max-voltage = <1800000>; rgltr-load-current = <3000>; status = "ok"; }; rear_main: qcom,cam-sensor@0 { cell-index = <0>; compatible = "qcom,cam-sensor"; csiphy-sd-index = <2>; eeprom-src = <&eeprom_rear_main>; actuator-src = <&actuator_rear_main>; ois-src = <&ois_rear_main>; sensor-position-roll = <90>; sensor-position-pitch = <0>; sensor-position-yaw = <180>; led-flash-src = <&led_flash_rear_main>; cam_vio-supply = <&cam_64c_ldo7>; cam_vdig-supply = <&cam_68c_ldo1>; cam_clk-supply = <&cam_cc_camss_top_gdsc>; cam_vana-supply = <&cam_68c_ldo7>; regulator-names = "cam_vana", "cam_vdig", "cam_clk", "cam_vio"; rgltr-cntrl-support; rgltr-min-voltage = <2800000 1100000 0 1800000>; rgltr-max-voltage = <2800000 1104000 0 1800000>; rgltr-load-current = <132000 405000 0 3000>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_mclk1_active &cam_sensor_active_rst1>; pinctrl-1 = <&cam_sensor_mclk1_suspend &cam_sensor_suspend_rst1>; gpios = <&tlmm 65 0>, <&tlmm 124 0>; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAMIF_MCLK1", "CAM_RESET1"; cci-master = ; clocks = <&camcc CAM_CC_MCLK1_CLK>; clock-names = "cam_clk"; clock-cntl-level = "nominal"; clock-rates = <24000000>; status = "ok"; }; rear_uw:qcom,cam-sensor@2 { cell-index = <2>; compatible = "qcom,cam-sensor"; csiphy-sd-index = <1>; sensor-position-roll = <90>; sensor-position-pitch = <0>; sensor-position-yaw = <180>; led-flash-src = <&led_flash_rear_uw>; actuator-src = <&actuator_rear_uw>; eeprom-src = <&eeprom_rear_uw>; cam_vio-supply = <&cam_64c_ldo7>; cam_vdig-supply = <&cam_68c_ldo2>; cam_clk-supply = <&cam_cc_camss_top_gdsc>; cam_vana-supply = <&cam_68c_ldo4>; regulator-names = "cam_vana", "cam_vdig", "cam_clk", "cam_vio"; rgltr-cntrl-support; rgltr-min-voltage = <2800000 1100000 0 1800000>; rgltr-max-voltage = <2800000 1104000 0 1800000>; rgltr-load-current = <148000 212000 0 3000>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_mclk0_active &cam_sensor_active_rst0>; pinctrl-1 = <&cam_sensor_mclk0_suspend &cam_sensor_suspend_rst0>; gpios = <&tlmm 64 0>, <&tlmm 123 0>; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAMIF_MCLK0", "CAM_RESET0"; cci-master = ; clocks = <&camcc CAM_CC_MCLK0_CLK>; clock-names = "cam_clk"; clock-cntl-level = "nominal"; clock-rates = <24000000>; status = "ok"; }; }; &cam_cci1 { eeprom_front: qcom,eeprom@1 { cell-index = <1>; compatible = "qcom,eeprom"; cci-master = ; cam_vio-supply = <&cam_64c_ldo7>; regulator-names = "cam_vio"; rgltr-cntrl-support; rgltr-min-voltage = <1800000>; rgltr-max-voltage = <1800000>; rgltr-load-current = <3000>; status = "ok"; }; actuator_front: qcom,actuator@1 { cell-index = <1>; compatible = "qcom,actuator"; cci-master = ; cam_vaf-supply = <&cam_64c_ldo6>; regulator-names = "cam_vaf"; rgltr-cntrl-support; rgltr-min-voltage = <2800000>; rgltr-max-voltage = <2800000>; rgltr-load-current = <95000>; status = "ok"; }; front_main: qcom,cam-sensor@1 { cell-index = <1>; compatible = "qcom,cam-sensor"; csiphy-sd-index = <3>; eeprom-src = <&eeprom_front>; actuator-src = <&actuator_front>; sensor-position-roll = <270>; sensor-position-pitch = <0>; sensor-position-yaw = <0>; cam_vio-supply = <&cam_64c_ldo7>; cam_vdig-supply = <&cam_64c_ldo1>; cam_clk-supply = <&cam_cc_camss_top_gdsc>; cam_vana-supply = <&cam_68c_ldo5>; regulator-names = "cam_vdig", "cam_clk", "cam_vana", "cam_vio"; rgltr-cntrl-support; rgltr-min-voltage = <1050000 0 2800000 1800000>; rgltr-max-voltage = <1050000 0 2800000 1800000>; rgltr-load-current = <125000 0 95000 3000>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_mclk3_active &cam_sensor_active_rst3>; pinctrl-1 = <&cam_sensor_mclk3_suspend &cam_sensor_suspend_rst3>; gpios = <&tlmm 67 0>, <&tlmm 126 0>; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAMIF_MCLK3", "CAM_RESET3"; cci-master = ; clocks = <&camcc CAM_CC_MCLK3_CLK>; clock-names = "cam_clk"; clock-cntl-level = "nominal"; clock-rates = <24000000>; status = "ok"; }; eeprom_tele: qcom,eeprom@3 { cell-index = <3>; reg = <0x03>; compatible = "qcom,eeprom"; cci-master = ; cam_vio-supply = <&cam_64c_ldo7>; regulator-names = "cam_vio"; rgltr-cntrl-support; rgltr-min-voltage = <1800000>; rgltr-max-voltage = <1800000>; rgltr-load-current = <1000>; status = "ok"; }; actuator_rear_tele: qcom,actuator@3 { cell-index = <3>; compatible = "qcom,actuator"; cci-master = ; cam_vio-supply = <&cam_64c_ldo7>; cam_vaf-supply = <&cam_64c_ldo5>; cam_v_custom2-supply = <&cam_ois_af_vdd_tele>; regulator-names = "cam_vio", "cam_vaf", "cam_v_custom2"; rgltr-cntrl-support; rgltr-min-voltage = <1800000 2800000 2800000>; rgltr-max-voltage = <1800000 2800000 2800000>; rgltr-load-current = <15000 130000 200000>; af-ois-use-same-ic; status = "ok"; }; ois_rear_tele: qcom,ois@3 { cell-index = <3>; compatible = "qcom,ois"; cci-master = ; cam_vio-supply = <&cam_64c_ldo7>; cam_vaf-supply = <&cam_64c_ldo5>; cam_v_custom2-supply = <&cam_ois_af_vdd_tele>; regulator-names = "cam_vio", "cam_vaf", "cam_v_custom2"; rgltr-cntrl-support; rgltr-min-voltage = <1800000 2800000 2800000>; rgltr-max-voltage = <1800000 2800000 2800000>; rgltr-load-current = <15000 130000 200000>; status = "ok"; }; rear_tele:qcom,cam-sensor@3 { cell-index = <3>; compatible = "qcom,cam-sensor"; csiphy-sd-index = <0>; sensor-position-roll = <90>; sensor-position-pitch = <0>; sensor-position-yaw = <180>; led-flash-src = <&led_flash_rear_tele>; eeprom-src = <&eeprom_tele>; actuator-src = <&actuator_rear_tele>; ois-src = <&ois_rear_tele>; cam_vio-supply = <&cam_64c_ldo7>; cam_vdig-supply = <&cam_64c_ldo2>; cam_clk-supply = <&cam_cc_camss_top_gdsc>; cam_vana-supply = <&cam_68c_ldo6>; regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana"; rgltr-cntrl-support; rgltr-min-voltage = <1800000 1050000 0 2800000>; rgltr-max-voltage = <1800000 1050000 0 2800000>; rgltr-load-current = <155000 680000 0 50000>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_mclk2_active &cam_sensor_active_rst2>; pinctrl-1 = <&cam_sensor_mclk2_suspend &cam_sensor_suspend_rst2>; gpios = <&tlmm 66 0>, <&tlmm 125 0>; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAMIF_MCLK2", "CAM_RESET2"; cci-master = ; clocks = <&camcc CAM_CC_MCLK2_CLK>; clock-names = "cam_clk"; clock-cntl-level = "nominal"; clock-rates = <24000000>; status = "ok"; }; };