#include #include &apps_rsc_drv2 { rpmh-regulator-ldob4 { compatible = "qcom,rpmh-vrm-regulator"; qcom,resource-name = "ldob4"; qcom,regulator-type = "pmic5-ldo"; qcom,supported-modes = ; qcom,mode-threshold-currents = <0 10000>; L4B: pm_humu_l4: regulator-pm-humu-l4 { regulator-name = "pm_humu_l4"; qcom,set = ; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; qcom,init-voltage = <1800000>; qcom,init-mode = ; }; }; }; &tlmm { /* tele s5kjn1 avdd*/ cam_avdd_tele_en_default: cam_avdd_tele_en_default { mux { pins = "gpio1"; function = "gpio"; }; config { pins = "gpio1"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ }; }; /* tele s5kjn1 dvdd*/ cam_dvdd_tele_en_default: cam_dvdd_tele_en_default { mux { pins = "gpio0"; function = "gpio"; }; config { pins = "gpio0"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ }; }; }; &soc { /* tele s5kjn1 avdd*/ cam_avdd_tele: gpio-regulator@0 { compatible = "regulator-fixed"; reg = <0x00 0x00>; regulator-name = "cam_avdd_tele"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; regulator-enable-ramp-delay = <233>; enable-active-high; gpio = <&tlmm 1 0>; pinctrl-names = "default"; pinctrl-0 = <&cam_avdd_tele_en_default>; vin-supply = <&BOB1>; }; /* tele s5kjn1 dvdd*/ cam_dvdd_tele: gpio-regulator@1 { compatible = "regulator-fixed"; reg = <0x01 0x00>; regulator-name = "cam_dvdd_tele"; regulator-min-microvolt = <1100000>; regulator-max-microvolt = <1100000>; regulator-enable-ramp-delay = <233>; enable-active-high; gpio = <&tlmm 0 0>; pinctrl-names = "default"; pinctrl-0 = <&cam_dvdd_tele_en_default>; vin-supply = <&S4G>; }; qcom,cam-res-mgr { compatible = "qcom,cam-res-mgr"; status = "ok"; }; }; &cam_cci0 { actuator_rear_main: qcom,actuator0{ cell-index = <0>; compatible = "qcom,actuator"; cci-master = ; cam_vaf-supply = <&camera_ldo7>; regulator-names = "cam_vaf"; rgltr-cntrl-support; rgltr-min-voltage = <2800000>; rgltr-max-voltage = <2800000>; rgltr-load-current = <119000>; status = "ok"; }; /* main s5kgn8 sensor*/ qcom,cam-sensor0 { cell-index = <0>; compatible = "qcom,cam-sensor"; csiphy-sd-index = <4>; actuator-src = <&actuator_rear_main>; sensor-position-roll = <90>; sensor-position-pitch = <0>; sensor-position-yaw = <180>; cam_vio-supply = <&L4B>; cam_vdig-supply = <&camera_ldo1>; cam_clk-supply = <&cam_cc_titan_top_gdsc>; cam_vana-supply = <&camera_ldo3>; cam_vaf-supply = <&camera_ldo7>; regulator-names = "cam_vana", "cam_vdig","cam_clk","cam_vio"; rgltr-cntrl-support; rgltr-min-voltage = <2200000 1000000 0 1800000>; rgltr-max-voltage = <2200000 1000000 0 1800000>; rgltr-load-current = <101000 787000 0 1000>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_mclk1_active &cam_sensor_active_rst2>; pinctrl-1 = <&cam_sensor_mclk1_suspend &cam_sensor_suspend_rst2>; gpios = <&tlmm 101 0>, <&tlmm 117 0>; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAMIF_MCLK1", "CAM_RESET1"; cci-master = ; clocks = <&camcc CAM_CC_MCLK1_CLK>; clock-names = "cam_clk"; clock-cntl-level = "nominal"; clock-rates = <24000000>; status = "ok"; }; /* tele s5kjn1 sensor*/ qcom,cam-sensor2 { cell-index = <2>; compatible = "qcom,cam-sensor"; csiphy-sd-index = <1>; sensor-position-roll = <90>; sensor-position-pitch = <0>; sensor-position-yaw = <180>; cam_vio-supply = <&L4B>; cam_vdig-supply = <&cam_dvdd_tele>; cam_clk-supply = <&cam_cc_titan_top_gdsc>; cam_vana-supply = <&cam_avdd_tele>; regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana"; rgltr-cntrl-support; rgltr-min-voltage = <1800000 1100000 0 2800000>; rgltr-max-voltage = <1800000 1100000 0 2800000>; rgltr-load-current = <3500 125000 0 95000>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_mclk2_active &cam_sensor_active_rst2>; pinctrl-1 = <&cam_sensor_mclk2_suspend &cam_sensor_suspend_rst2>; gpios = <&tlmm 102 0>, <&tlmm 118 0>; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAMIF_MCLK2", "CAM_RESET2"; cci-master = ; clocks = <&camcc CAM_CC_MCLK2_CLK>; clock-names = "cam_clk"; clock-cntl-level = "nominal"; clock-rates = <24000000>; status = "ok"; }; }; &cam_cci1 { eeprom_front: qcom,eeprom@1 { cell-index = <1>; compatible = "qcom,eeprom"; cci-master = ; cam_vio-supply = <&L4B>; regulator-names = "cam_vio"; rgltr-cntrl-support; rgltr-min-voltage = <1800000>; rgltr-max-voltage = <1800000>; rgltr-load-current = <3000>; status = "ok"; }; /* temp set ldo2 1.2V */ qcom,cam-sensor1 { cell-index = <1>; compatible = "qcom,cam-sensor"; csiphy-sd-index = <5>; sensor-position-roll = <270>; sensor-position-pitch = <0>; sensor-position-yaw = <0>; eeprom-src = <&eeprom_front>; cam_vio-supply = <&L4B>; cam_vdig-supply = <&camera_ldo2>; cam_clk-supply = <&cam_cc_titan_top_gdsc>; cam_vana-supply = <&camera_ldo4>; regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana"; rgltr-cntrl-support; rgltr-min-voltage = <1800000 1104000 0 2800000>; rgltr-max-voltage = <1800000 1104000 0 2800000>; rgltr-load-current = <10000 140400 0 52000>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_mclk4_active &cam_sensor_active_rst4>; pinctrl-1 = <&cam_sensor_mclk4_suspend &cam_sensor_suspend_rst4>; gpios = <&tlmm 104 0>, <&tlmm 120 0>; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAMIF_MCLK4", "CAM_RESET4"; cci-master = ; clocks = <&camcc CAM_CC_MCLK4_CLK>; clock-names = "cam_clk"; clock-cntl-level = "nominal"; clock-rates = <24000000>; status = "ok"; }; };