#include <dt-bindings/clock/qcom,gcc-monaco.h>
#include <dt-bindings/interconnect/qcom,monaco.h>

&soc {
	/* Primary USB port related controller */
	usb0: hsusb@4e00000 {
		compatible = "qcom,dwc-usb3-msm";
		reg = <0x4e00000 0x100000>;
		reg-names = "core_base";

		#address-cells = <1>;
		#size-cells = <1>;
		ranges;

		interrupts = <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>,
			<GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-names = "pwr_event_irq", "hs_phy_irq";

		clocks = <&gcc GCC_USB20_MASTER_CLK>,
			<&gcc GCC_CFG_NOC_USB2_PRIM_AXI_CLK>,
			<&gcc GCC_SYS_NOC_USB2_PRIM_AXI_CLK>,
			<&gcc GCC_USB2_PRIM_CLKREF_CLK>,
			<&gcc GCC_USB20_SLEEP_CLK>,
			<&gcc GCC_USB20_MOCK_UTMI_CLK>;
		clock-names = "core_clk", "iface_clk", "bus_aggr_clk",
				"xo", "sleep_clk", "utmi_clk";

		resets = <&gcc GCC_USB20_PRIM_BCR>;
		reset-names = "core_reset";

		USB3_GDSC-supply = <&gcc_usb20_prim_gdsc>;
		dpdm-supply = <&usb2_phy0>;
		extcon = <&eud>;

		qcom,core-clk-rate = <60000000>;
		qcom,default-bus-vote = <2>; /* use svs bus voting */

		interconnect-names = "usb-ddr", "usb-ipa", "ddr-usb";
		interconnects = <&system_noc MASTER_USB3 &bimc SLAVE_EBI_CH0>,
				<&system_noc MASTER_USB3 &config_noc SLAVE_IPA_CFG>,
				<&bimc MASTER_AMPSS_M0 &config_noc SLAVE_USB3>;

		qcom,pm-qos-latency = <2>;
		qcom,num-gsi-evt-buffs = <0x3>;
		qcom,gsi-reg-offset =
			<0x0fc /* GSI_GENERAL_CFG */
			0x110 /* GSI_DBL_ADDR_L */
			0x120 /* GSI_DBL_ADDR_H */
			0x130 /* GSI_RING_BASE_ADDR_L */
			0x144 /* GSI_RING_BASE_ADDR_H */
			0x1a4>; /* GSI_IF_STS */

		dwc3@4e00000 {
			compatible = "snps,dwc3";
			reg = <0x4e00000 0xcd00>;

			iommus = <&apps_smmu 0x120 0x0>;
			qcom,iommu-dma = "atomic";
			qcom,iommu-dma-addr-pool = <0x50000000 0x60000000>;

			interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
			usb-phy = <&usb2_phy0>, <&usb_nop_phy>;
			snps,disable-clk-gating;
			snps,is-utmi-l1-suspend;
			snps,dis-u1-entry-quirk;
			snps,dis-u2-entry-quirk;
			snps,dis_u2_susphy_quirk;
			snps,dis_enblslpm_quirk;
			snps,has-lpm-erratum;
			snps,hird-threshold = /bits/ 8 <0x0>;
			maximum-speed = "high-speed";
			dr_mode = "otg";
		};

		qcom,usbbam@0x04f04000 {
			compatible = "qcom,usb-bam-msm";
			reg = <0x04f04000 0x17000>;
			interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>;

			qcom,usb-bam-fifo-baseaddr = <0xc121000>;
			qcom,usb-bam-num-pipes = <4>;
			qcom,disable-clk-gating;
			qcom,usb-bam-override-threshold = <0x4001>;
			qcom,usb-bam-max-mbps-highspeed = <400>;
			qcom,reset-bam-on-connect;

			qcom,pipe0 {
				label = "hsusb-qdss-in-0";
				qcom,usb-bam-mem-type = <2>;
				qcom,dir = <1>;
				qcom,pipe-num = <0>;
				qcom,peer-bam = <0>;
				qcom,peer-bam-physical-address = <0x08064000>;
				qcom,src-bam-pipe-index = <0>;
				qcom,dst-bam-pipe-index = <0>;
				qcom,data-fifo-offset = <0x0>;
				qcom,data-fifo-size = <0x1800>;
				qcom,descriptor-fifo-offset = <0x1800>;
				qcom,descriptor-fifo-size = <0x800>;
			};
		};
	};

	/* Primary USB port related High Speed PHY */
	usb2_phy0: hsphy@1613000 {
		compatible = "qcom,usb-hsphy-snps-femto";
		reg = <0x1613000 0x120>,
			<0x01612000 0x4>;
		reg-names = "hsusb_phy_base",
			"eud_enable_reg";

		vdd-supply = <&L12A>;
		vdda18-supply = <&L14A>;
		vdda33-supply = <&L25A>;
		qcom,vdd-voltage-level = <0 904000 904000>;

		clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
		clock-names = "ref_clk_src";

		resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
		reset-names = "phy_reset";
		qcom,param-override-seq =
			<0x63 0x6c	/* override_x0 */
			 0xC8 0x70	/* override_x1 */
			 0x17 0x74>;	/* override x2 */
	};

	usb_nop_phy: usb_nop_phy {
		compatible = "usb-nop-xceiv";
	};

};